Since 1973
Catalog
After Hours Service
Contact Us
button-CAN-50.png
1.800.387.7115
button-USA-25.png
1.877.432.3627

Home >> Shaft Seals

Shaft Seals

Daemar’s extensive line up of shaft seal products has been developed to provide exceptional value by combining the quality and performance that design engineers require with the total cost of ownership savings that today’s businesses demand.

 

lg_oil_seals2_200

Oil Seals

A complete selection of Inch & Metric sizes of DMR Rotary shaft seals.  Available in a range of compounds and a wide selection of oil seal lip styles.

Bearing Isolators Protech seals

DMR Bearing Isolators

Bearing isolators (Protech seals) are designed to protect bearings with zero lubricant leakage and total exclusion of contaminants.

Daemar DMR Parker Clipper Seals

JM Clipper Seals

A complete selection if JM Cliiper shaft seals in inch and metric shaft sizes.  JM Clipper seal sizes ranging from below one inch to well over 40 inches OD.

lg_axleseals-200

Axle Seals

design, used in environments where outside contamination can damage the sealing lip. Typical applications include axles of trucks, trailers and off-road vehicles.

 

lg_dmr_wheelhubseals_group_03_200

Wheel Hub Seals

DMR™ Wheel Hub Seals protect bearings and shafts during operation, installation and removal by providing a built-in wear sleeve and rubber coated metal casings.

lg_va_series_200

V-Rings

V-Rings are all-rubber seals that seat directly on the shaft and seal axially against a counterface, housing, seal case or similar surface.

lg_end_covers_185

End Covers

For gear box applications where the shaft does not pass through the housing wall, end covers are used to seal bearings. Designed to fit into housing bores for rotary shaft lip seals which means that a shaft can easily be left or right-hand oriented. The inner housing is carbon steel and the outer seal is nitrile rubber.

PTFE Finger Spring Seal

Teflon Energized Seals

Used in applications where ultra-low friction, chemical compatibility, long life and extreme temperature performance is required.

 

lg_DMR_HighPressure_PTFESeal-02_200

High Pressure PTFE Seals

Excellent for extreme temperatures, high pressures high speeds and corrosive liquids & gases. Our equivalent to Garlock P.S. and Elring styles.

lg_l2m-seal-02_200

L2M Seals

L2M is a rolling mill bearing seal. Every design feature was based on the extra demands of rolling mill service – including the demand for lower cost. Even though the term “rolling mill” is usually associated with the aluminum and steel industry, with this seal, we include the paper industry.

dmr-mechanical-seal-single-spring-type-c

Mechanical Seals 

Mechanical pump seals are cost effective for a wide range of applications such as pool and spa pumps, centrifugal pumps and well point pumps. We also provide multi-spring seals

Daemar DMR Hydraulic Seals

Hydraulic Seals

Hydraulic seals are  for earth moving/construction machinery, agriculture machinery, agricultural/forestry machinery, material handling, industrial hydraulics, vehicle engineering and mining.

 

dmr-o-rings-sanitary-tri-clamp-gaskets

Metal Detectable Seals

Seals molded in standard elastomers with a metal impregnated compound that allows rubber fragments to be located by an in-line metal detector. This alarm enables your system to instantly reject contaminated product.

dmr-hammer-union-seals

Hammer Union Seals

Union Seals are available in 1” to 4” line pipe sizes and materials including: 80 Nitrile, 80 Viton, 90 Viton, 80 HNBR. Available in Guiberson and Weco Styles.

dmr-o-rings-sanitary-tri-clamp-gaskets

Sanitary Gaskets

Sanitary Gaskets are used widely in the Food, Dairy, Beverage, Biotech, Pharmaceutical, and all other Sanitary Process industries to seal clamp connections in sanitary pipe lines.

dmr babsl oil seals

BABSL Seals

BABSL high pressure rotary seals, available in metric and imperial sizes to suit a wide variety of applications. Pressure resistant style for use without back-up ring, dust lip to protect against outside contaminants.

Large Diameter Seals

A wide range of large diameter seals, custom manufactured as either cast urethane seals or CNC machined seals (in a range of materials). Seals are available in both imperial and metric sizes with more than 1200 molds in stock for large diameter U-cup seals up to 32½” OD and in-house manufacturing capabilities to produce custom molds and seals up to 34″ OD.

Trelleborg Sealing Solutions

Trelleborg Sealing Solutions’ range of products includes hydraulic seals, pneumatic seals, shaft seals, oil seals and other rotary seals, mechanical face seals / heavy duty seals, aircraft seals and a broad variety of static seals.

DMR Camlock Gasket

Encapsulated Camlock Gaskets

Manufactured to the highest standards to ensure optimum reliability. Stock can be ordered on all standard main seal sizes for cam and groove hose couplings with production capability to meet the highest volume demands.

 

 

shaft-seal-150

SEAL

dmr-wave-springs-multiturn-single

RETAIN

caplug-500

PROTECT

dryslide-150-2

SLIDE

DMR_SlottedShim_A-075-150x150

ALIGN

Translate »
Scroll to Top